|
merv
|
 |
« on: September 20, 2013, 08:39:35 AM » |
|
Can any one tell me where I can get new diff casing studs and domed stainless nuts from,
any help would be appreciated
Thanks
Merv
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
merv
|
|
« Reply #1 on: September 20, 2013, 10:31:45 PM » |
|
Well
can any one help, if not how do I put my diff back together
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
steven brock
|
|
« Reply #2 on: September 21, 2013, 08:16:09 AM » |
|
Think they 5/16 unf maybe good ole eBay.. from memory I think to replace them seemed expensive for dome nuts
|
|
|
|
|
Logged
|
steel wasn't invented to make bloody staples with!
|
|
|
|
merv
|
|
« Reply #3 on: September 21, 2013, 08:42:58 AM » |
|
Thanks Steve
Sounds like the studs are hard to come by, if I had known I would not have thrown the studs out when I stripped the axle, doh.
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
Olds
|
|
« Reply #4 on: September 21, 2013, 08:52:15 AM » |
|
How bad are the old studs?
Without pulling the studs from my axle I'm not sure but they may be unf at the nut end but I would expect them to be unc in the casing.
Better check this.
Various lengths are available via ebay
|
|
|
|
|
Logged
|
Getting older but no wiser! Just using bigger hammers.
The answer to most problems, fire and lots of it.
|
|
|
|
Olds
|
|
« Reply #5 on: September 21, 2013, 08:59:14 AM » |
|
OK have removed a stud.
Yep 5/16" unf - unc x 2" long. Thread lengths each end approx. 5/8" (16mm)
You should be able to find some manifold studs that size.
Hope that helps.
|
|
|
|
|
Logged
|
Getting older but no wiser! Just using bigger hammers.
The answer to most problems, fire and lots of it.
|
|
|
|
merv
|
|
« Reply #6 on: September 21, 2013, 09:01:55 AM » |
|
Hi Old's
The thing is I haven't got them I threw them away when I stripped the axle, my thinking was to buy new.
Been looking on eBay cant seem to find any maybe using the wrong terminology or wording
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
merv
|
|
« Reply #7 on: September 21, 2013, 09:04:52 AM » |
|
Thanks Old's
Would the reliant exhaust studs be the same?
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
Olds
|
|
« Reply #8 on: September 21, 2013, 09:10:01 AM » |
|
|
|
|
|
|
Logged
|
Getting older but no wiser! Just using bigger hammers.
The answer to most problems, fire and lots of it.
|
|
|
|
hunter
|
|
« Reply #9 on: September 21, 2013, 09:13:32 AM » |
|
|
|
|
|
|
Logged
|
I
|
|
|
|
merv
|
|
« Reply #10 on: September 21, 2013, 09:20:44 AM » |
|
Hi hunter
Thanks, I don't know at the moment, hey Old's you still reading sorry to be a nuisance but the link hunter sent through would they suit ?
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
Olds
|
|
« Reply #11 on: September 21, 2013, 09:24:03 AM » |
|
Not really. To short and are for screwing into a cast iron manifold, the unc section is less than 10mm long.
|
|
|
|
« Last Edit: September 21, 2013, 09:48:39 AM by Old Newbie »
|
Logged
|
Getting older but no wiser! Just using bigger hammers.
The answer to most problems, fire and lots of it.
|
|
|
|
hunter
|
|
« Reply #12 on: September 21, 2013, 09:38:46 AM » |
|
|
|
|
|
|
Logged
|
I
|
|
|
|
merv
|
|
« Reply #13 on: September 21, 2013, 09:54:02 AM » |
|
Thanks you two, you both have been a great help
|
|
|
|
|
Logged
|
Why do every five minute job take all day, and
if it can go wrong it will go wrong
|
|
|
|
Olds
|
|
« Reply #14 on: September 21, 2013, 10:12:52 AM » |
|
S'OK.  Just check that the unc section is at least 14mm otherwise the risk of pulling the ally threads is a lot higher. |
|
|
|
|
Logged
|
Getting older but no wiser! Just using bigger hammers.
The answer to most problems, fire and lots of it.
|
|
|
|
