I have seen a couple of post relating to lads and lassies wanting to convert from points to electronic ignition .
Perhaps the following link to an article I did a wee while ago might be helpful
https://sites.google.com/site/fifersrelianthintsandtips/electronic-conversions/how-to-fit-a-simonbbc-electronic-kit
..
Following info added on 19 January 2012Unless you are very lucky , due to the new positions of the electronic pickups in relation to the distributor cam , when the Simonbbc electronic doodahs are fitted you will need to slacken off the side distributor clamp and rotate the distributor body by hand till it fires . You might have to move it a fair wee bit
I would recommend that you set up the engine in the best position with the original points in place before fitting the electronic doodahs .
{ 1 } Set the engine statically at the 10 degrees Before Top Dead Centre mark on the fan belt pulley with the rotor arm pointing at number 1 cylinder { the one at the front of the engine }.
ELECTRONIC IGNITION ; A HOW TO CONVERT GUIDE
http://i423.photobucket.com/albums/pp316/fifer3w/R3W/timing-1.jpg{ 2 } Switch the Ignition OFF
{ 3 } Remove distributor
{ 4 } Clean Distributor body including clamp { If required }
{ 5 } Mark a line across the Distributor body and the clamp with tippex / paint / scribe so that if you want to revert back to points you will know where the original setting was
{ 6 } Fit the new electronic parts as per
https://sites.google.com/site/fifersrelianthintsandtips/electronic-conversions/how-to-fit-a-simonbbc-electronic-kit{ 7 } Slacken off the side clamp pinch bolt
{ 8 } Fit the distributor back into the engine
{ 9 } Rotate the distributor body till the bolt hole in the engine clamp slot is midway { This is so that you can still get a bit of movement to re-adjust the timing in the future }
{ 10 } Fit the bolt , spring washer and washer and tighten
{ 11 } Wire up as per instructions below
ELECTRONIC IGNITION ; A HOW TO CONVERT GUIDE
http://i423.photobucket.com/albums/pp316/fifer3w/R3W/DISTRIBUTOR/1ELECTRONICKITFROMSIMONBBCpriort-2-1.jpgRemember and insulate joins on both wires to stop shorting against the distributor body .
{ 12 } Turn the distributor body around by hand and align the marks you previously made { the body should be slack enough to turn but not too slack } . If too slack just tighten up the side clamp bolt a wee bit till you can turn it smoothly without a jerky motion .
{ 13 } Try to start the engine while holding the distributor body in place to stop it from moving . If it starts you are a lucky Bugg*r and you can go to { 20 }
{ 14 } If it does not start
{ 15 } Stop trying to start the engine .
{ 16 } Turn the distributor clockwise roughly about 1/4 inch { 6mm or so }
{ 17 } Try to start the engine while holding the distributor body in place to stop it from moving ..
{ 18 } If it starts and runs just stop the engine
{ 19 } If it does not start just keep VERY slowly rotating the distributor body till it fires and runs then
{ 20 } Stop the engine
{ 21 } Put a temporary mark on the distributor and clamp
{ 22 } Tighten up the side clamp pinch bolt
{ 23 } Start the engine and get up to working temperature
{ 24 } Stop the engine
{ 25 } Slacken off the pinch bolt enough to be able to rotate the distributor smoothly .
{ 26 } Holding the distributor body , start the engine and VERY slowly turn the distributor body clockwise to try and get the fastest tickover .
If it cuts out just rotate it back to the Original good mark and try again .
{ 27 } When you have reached what you think is the best point then just
{ 28 } Stop the engine
{ 29 } Tighten up the side clamp pinch bolt
{ 30 } Mark a line across the Distributor body and the clamp with tippex / paint / scribe so that if you will know where the setting was .
{ 31 } Set the Timing { if required } by strobe
{ 32 } In the future all you have to do is leave the side pinch bolt alone and slacken off the clamp plate to engine bolt to get adjustment either way Smiley
.
I wrote this early in the morning just from memory { and that is bad } so if I have made a wee mistake here and there please feel free to chastise me and I will go and give myself a darn good thrashing
.
.